DATAC V3 complete pack for Bulldog .357

The pack includes:

-1X Benjamin Bulldog .357 sound enhancement kit/ Depinger V3 kit

-1X DATAC® V3 Carbon Nylon Sound Moderator for Bulldog.357

-1X MKII single-shot magazine 9mm caliber

-5Xbarrel centralizers

Big guns go big!

DATAC® V3 Nylon Carbon sound moderator for Bulldog.357:

Robust, light and high-end , the DATAC ® V3 sound moderator made entirely of Carbon Nylon is designed to provide you with discretion and comfort during your shooting sessions. It makes the bulldog.357 fully usable indoors and gardens from a sound point of view.

*makes the shot more discreet by 25 to 28 db.

Product weight: 130g

installed product length: 180mm

The DATAC® V3 Nylon Carbon suppressor will replace the factory cap on your Benjamin Bulldog and fits perfectly into the environment of your weapon.

Material: PA-12CF (Carbon nylon)

Composition: PA-12 CF (Nylon carbon) , high-end nylon alloy reinforced with carbon fiber. Heavyweight champion in impact and high temperature resistance. Used in particular in the aeronautical and automobile industries for its exceptional and unrivaled properties.

Simpler installation than ever:

-remove the factory cap using a 3/32 Allen key

-insert the V3 in place of the original cap by hand, without using tools such as a sledgehammer, mallet or hammer or other.

-fix the V3 using the carbon steel screws provided, the 12mm one on the lower rail side, the 8mm one on the upper side. Be careful to use the screws supplied with the V3 because the thread used is in metric units and not in inches like that present on the original part.

depinger V3 kit:

New version V3 of the DEPINGER DATAC kit, even more efficient, even easier to install.

Because structure governs function, the DEPINGER MKIII Kit is specifically developed to offer unprecedented vibration absorption power when shooting. thereby removing the "Ping" sound effect resonating in your weapon's air tank with each shot. You thus gain hearing comfort and discretion.

Installing the kit:

- Gently empty the entire air reserve via the bleed screw located in front of the kick connect valve. Wait 15 minutes for all the air to be evacuated.

-Remove the barrel protection casing using 2 screws at the front and one at the rear on the upper face, then push it forward to reveal the barrel

-Detach the flexible plastic butt plate from your rifle.

-Remove the upper left (2 screws) and right (5 screws) covers covering the lever/reset system of the rifle.

-Remove the lower left (4 screws) and right (10 screws) covers.

-Extract the rifle system including the barrel/reservoir/trigger block... from the plastic covers.

-Unscrew the tank at its base, being careful not to unscrew its adapter/connector (it will be normal for the tank to be difficult to unscrew)

- Place the diabolo-shaped Depinger at the entrance to the tank tube.

-Using the cylinder, drive the depinger inside the tank along the entire length of the cylinder.

-Remove the cylinder

-Your Depinger is now in place

-Optional: apply a thin strip of Teflon to the thread of the tank before assembly to ensure watertightness.

-Reassemble the rifle.

Congratulations, you have just installed your depinger kit!

Installation of centralizers:

- For safety reasons, carefully empty the entire air tank via the bleed screw located in front of the kick connect valve. wait 15 minutes for all the air to be evacuated.

- Dismantle the barrel protection casing using 2 screws at the front and one at the rear on the upper side, then push it forward to reveal the barrel

-Detach the flexible plastic butt plate from your rifle.

Allow approximately 15 minutes for installation.

-Remove the star at the end of the barrel (it is normal that it comes with difficulty).

-Insert the barrel centralizer(s) along the barrel.

-Reassemble the rifle.

Congratulations you have just installed your barrel centralizers.

MKII single-shot magazine cal.357 for Benjamin Bulldog:

Fits perfectly in place of the original charger.

Its ergonomic design offers a better grip while preserving appreciable freedom when handling the reloading of your rifle.

DATAC your accessories professional in the field of armaments.

Product protected by intellectual property rights, any misappropriation/reproduction of our products will give rise to legal proceedings.

Please note, this product is not compatible with the use of JSB and H&N Sport pellets due to their too short profile. Leads can deviate in the moderator due to pressure variations between each cell and cause damage. The minimum recommended projectile weight is 130 grains.

FDM / X-CF production

Benjamin bulldog .357 + scope not supplied